New Membership Platform: Membee

The ACD Club is rolling out a new online membership system. All ACD Club Members should have receivied an email with enrollment instructions. You will use your email address as your login, and select a new password. This account will be used to renew your membership, update membership information, and make changes to your membership record.


This account is NOT THE SAME as your current account which you use to access the ACD Website Forums. Please continue to log into the Forums with the same username and password as you have always used. In the future we may consolidate the two accounts.

How to change the cross shift diaghram?

  • alsancle
  • alsancle's Avatar Topic Author
  • Offline
  • ACD Club Member
  • ACD Club Member
More
18 May 2021 23:54 #43202 by alsancle
How to change the cross shift diaghram? was created by alsancle
I've ordered a new diaphragm and seal for the cross shift assembly. However, I do not have enough space to get the housing off. See the picture. Even with the cross shaft moved all the way over to the right, I still need another 1/2 an inch or so.

Do I have to remove the passenger side fender? Or is it easier to pull the front cover off the transmission? Suggestions?

Attachments:

Please Log in or Create an account to join the conversation.

  • JIM.OBRIEN
  • Offline
  • Frequent Forum Contributor
  • Frequent Forum Contributor
More
19 May 2021 02:04 #43204 by JIM.OBRIEN
Replied by JIM.OBRIEN on topic How to change the cross shift diaghram?
Pull the cross shift off the front of the transmission.
1. Disconned the rod from the main shift cylinder (remove the cotter pin and pull the pin out).
2. Disconnect the oil line from the filter at the center bottom of the cross shift housing.
3. Remove the wires from the cross shift swotch.
4. Remove the 6 bolts holding the cross sift houseing to the transmission - note which bolts come out of which hole - the bolts are three different lengths.
5. Remove the housing. You have to pull it straight towards the front of the car to get the pipe out of the top shaft and then wiggle it around to disengage the dogbone from the shift rails.

Look at the article in Newsletter #2 this year for mor info on the cross shifter.
The following user(s) said Thank You: alsancle

Please Log in or Create an account to join the conversation.

More
19 May 2021 02:08 #43205 by Mike Brady
Replied by Mike Brady on topic How to change the cross shift diaghram?
PM Sent

Please Log in or Create an account to join the conversation.

  • mikespeed35
  • mikespeed35's Avatar
  • Offline
  • ACD Club Life Member
  • ACD Club Life Member
More
19 May 2021 03:59 #43207 by mikespeed35
Replied by mikespeed35 on topic How to change the cross shift diaghram?
Just a comment. The three different size bolts you speak of may not have been installed correctly last time this part was removed! Best check before putting them back same way.
CORDiallyMike

Mike Huffman
The following user(s) said Thank You: alsancle

Please Log in or Create an account to join the conversation.

  • alsancle
  • alsancle's Avatar Topic Author
  • Offline
  • ACD Club Member
  • ACD Club Member
More
19 May 2021 11:16 #43209 by alsancle
Replied by alsancle on topic How to change the cross shift diaghram?
Thanks Guys! I will be tackling this project next week.

Please Log in or Create an account to join the conversation.

  • Terry Cockerell
  • Terry Cockerell's Avatar
  • Offline
  • Frequent Forum Contributor
  • Frequent Forum Contributor
More
19 May 2021 20:50 - 19 May 2021 20:51 #43213 by Terry Cockerell
Replied by Terry Cockerell on topic How to change the cross shift diaghram?
Attached is a picture showing the the leather diaphragm and slotted connection to the cross shaft.

T cockerell
Attachments:
Last edit: 19 May 2021 20:51 by Terry Cockerell. Reason: Adding picture
The following user(s) said Thank You: alsancle

Please Log in or Create an account to join the conversation.

Time to create page: 0.116 seconds
Powered by Kunena Forum